Author Topic: 6 " Flat Belt Green Jacket Circulation Pump  (Read 2537 times)

EMU

  • Member
  • *
  • Posts: 77
6 " Flat Belt Green Jacket Circulation Pump
« on: 24 June, 2018, 09:24:18 pm »
Hi , Guys , I have joined TOMM to seek advise and other and share detail and information .
I was provided a Flat Belt , Green Jacket Water Circulation Pump . 1' 1/4 inlet , 1' 1/4 outlet .
The Pump has No  ' ID ' as in Stamping . It has a Brass Centrifuge , Held in place by 2 screws , which at present only has 1 which I will install the additional screw. Visual inspection shows thread opposing for an additional screw to keep it flat and central . There is a Clamp which enables the positioning of the Centrifuge Jacket to be locked in place , depending on the desired position of the Outlet within a 360 ' turn .
It looks quite  similar to a Stover ODX , DX water cooling circulation pump .
I understand that Stover manufactured their own Pumps , although I am in the opinion that Cooper / Stover rebadge supplied their own manufactured pumps  , for the ODX , DX type Machines Horizontal Hit / Miss on Bettendorf Transport or Truck , horse drawn , with Cooling Tank .
Information in relation to this Pump , much appreciated .   

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #1 on: 24 June, 2018, 09:26:45 pm »
Inside Jacket

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #2 on: 24 June, 2018, 09:34:39 pm »
End view .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #3 on: 24 June, 2018, 09:44:25 pm »

I have used the Term '' Green Jacket '' as searching Ebay , shows a ' Red Jacket Pump '  ''' almost ''' identical to the Pump in question made in America . Maybe for Fair Banks and Morse , who knows ?!!.
Is it possible or highly likely that Cooper manufactured their own Circulation Pumps for specific duties and possible for their Rebadge Machines . I don't seem to think it is a IBC . The time period too early , for IBC .
Is it a Cooper Bessemer . ?  [Cooper Bessemer Engineering ] '' CBE '' . 

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #4 on: 25 June, 2018, 05:38:43 am »
If ' one' desired a 'V' belt pulley [ sheave ] ' could be installed at the very end of the shaft , if room is critical .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #5 on: 25 June, 2018, 05:42:12 am »
Red Jackets

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #6 on: 25 June, 2018, 05:42:46 am »
Red Jacket

cobbadog

  • Member
  • *
  • Posts: 3173
  • Buzacott Farm Pumper.
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #7 on: 25 June, 2018, 04:27:28 pm »
Apart from the pulley set up there is a big difference between the 'red' pumps and yours. That is yours has an end plate or cap where the water inlet is and the other 2 are a single cast and the body rotates with the end plate.
Cheers, John & Dee. Coopernook. NSW.

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #8 on: 25 June, 2018, 06:40:35 pm »
I just have enough ' meat ' on the End of The Central Shaft for a ' V' Belt Sheave ?

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #9 on: 30 June, 2018, 04:20:29 pm »
6 'Inch  Green Jacket Water Cooling Circulation Pump to Fit this Cooper / Stover .

tim

  • Member
  • *
  • Posts: 218
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #10 on: 01 July, 2018, 10:32:12 am »
Hi EMU,
It is different to a F-M.  I'd say it's original.
Have you been in contact with Joe Maurer with the stover engine registry?  He may be able to help. 
He can also give you the original shipping details.

Cheers,
Tim
Central West, NSW

peter dixon

  • Member
  • *
  • Posts: 28
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #11 on: 01 July, 2018, 06:58:45 pm »
hi,
looking closely at the photo of a good looking resto, the transport looks identical (tho not as rust damaged) as the 7hp Alamo I am slowly working on.  is it the original transport?    can send pic of mine via phone if interested  not clever enough to get pic from phone to computer 0428136158

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #12 on: 02 July, 2018, 12:25:30 pm »
Tim  , same mica disc size and mica tube as F&M Igniter .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #13 on: 02 July, 2018, 12:35:19 pm »
Peter Dixon , yes Original Bettendorf Truck or [cart]. With in bold lettering ' CARNEGIE ' stamped in Steel Section . Which is unique and enabled me to find detail of Whom he was .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #14 on: 02 July, 2018, 12:38:09 pm »
Confirmation ,
 Stover made several circulation pumps for their Engine applications , this is one of them .