Author Topic: 6 " Flat Belt Green Jacket Circulation Pump  (Read 2581 times)

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #15 on: 02 July, 2018, 12:45:16 pm »
The above ' subject 'Green Cooper / Stover Circulation Pump spins only in a CW direction , same as Engine Direction . CW from belt drive End . So this Pump can only be mounted in its Original Rear Transport Mounting Holes adjacent to Cooling Tank .

peter dixon

  • Member
  • *
  • Posts: 28
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #16 on: 02 July, 2018, 05:16:38 pm »
googled Bettendorf. looks like they made transporters for many engine manufacturers. thanks for the info

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #17 on: 03 July, 2018, 05:46:23 pm »
Confirmed
 Shaft is 5/8 , Grease Nipple for Shaft 3/8 UNF .
Pump Inlet and Outlet thread 1' 1/4 - 12 TPI UNF .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #18 on: 03 July, 2018, 05:50:44 pm »
Correction : this Pump can be Operated in either direction of Rotation by Turning Around the Impellor .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #19 on: 03 July, 2018, 05:52:49 pm »
Boltmasters

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #20 on: 03 July, 2018, 06:08:40 pm »
Correction , impellor can be turned round , so it can be operated in CW [ Rear Mount ] & CCW [ Front Mount |.

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #21 on: 04 July, 2018, 06:07:30 pm »
Bolt found on Pump Shaft Hold Down .

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #22 on: 06 July, 2018, 06:57:42 pm »
Asking so kindly , what position does the Large Brass Nut ' Centre ' need to be in . ? Just firm against the Flat Belt Sheave or Backed away . Or up against the Locking Clamp , to the right . ?

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #23 on: 06 July, 2018, 07:15:56 pm »
The Brass Nut does not Rotate when Pump is activated .
The Flat Belt Sheave , has a Keeper Screw as shown , to prevent it from drifting and spinning on its own accord .
Could the Brass Nut be just up near The Flat Belt Sheave as a Safety with a minimal Gap ..

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #24 on: 06 July, 2018, 09:18:02 pm »
Ok , I have been informed , of the r

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #25 on: 06 July, 2018, 09:23:25 pm »
Ok , I have been informed of the Works of The Brass Nut ,
Wind back the Brass Nut as Far as it will go ,to reveal inner shaft , obtain Hessian String , Feed the String turning the shaft as ' you ' go onto the shaft with grease , when the desired amount of String Packing is reached , Close the Brass Nut , to compress the Matrix . Up against the Flat Belt Sheave . I suppose it is called a Gland Nut .

cobbadog

  • Member
  • *
  • Posts: 3181
  • Buzacott Farm Pumper.
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #26 on: 07 July, 2018, 02:40:01 pm »
Yep a gland nut is what it is. As for the position of the flat belt pulley you can position it anywhere it suits you to enable it to align with the drive pulley. As you already are aware, it must be clear of other none moving parts.
Cheers, John & Dee. Coopernook. NSW.

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #27 on: 07 July, 2018, 05:07:17 pm »
Thank you for this information .  Slowly getting there  . Atleast so far the pump is attached ehere it should be . Tank is a too wide , although i am not changing it . Narower Tank or Circular i reckon . Which then would provide room too move it closer to enable Flat Belt to be used 

EMU

  • Member
  • *
  • Posts: 77
Re: 6 " Flat Belt Green Jacket Circulation Pump
« Reply #28 on: 12 July, 2018, 06:36:43 pm »
Made by IBC Little Rock Arkansas  America